Basic Info.
Max Diameter of Workpiece
<500mm
Mass Scope of Workpiece
<900kg
Type
Tensile Testing Machine
Distance Between Columns
520mm
Diameter of Round Specimen
φ10-φ40mm
Thickness of Flat Specimen
2-30mm
Compression Platen
φ150mm
Actuator (Piston) Stroke
150mm
Actuator (Piston) Speed
0-140mm/Min
Max. Compression Space
630mm
Transport Package
Fumigated Wooden Case
Specification
3800 x 2905 x 3880 mm
Product Description
Tensile Testing Machine 600kN Tension Testing of Metallic Materials ASTM E8 HUT605A-TP
This 600kN servo hydraulic universal testing machine is built with 6 columns. Dual zone (tension on top, compression on bottom) is more convinient to perform tension and compression test.Worm-wheel driven crosshead to adjust the test space satisfies various length specimen.
Typical specimens:
Fasteners, rebar, chain, welds, castings
Test Standard: ASTM E8
Standard Test Methods for Tension Testing of Metallic Materials
Scope*
1.1 These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation,tensile strength, elongation, and reduction of area.
NOTE 1-These test methods are the metric companion of Test Methods E 8. Committee E-28 was granted an exception in 1997 by the Committee on Standards to maintain E8 and E8M as separate companion standards rather than combining standards as recommended by the Form and Style manual.
NOTE 2-These metric test methods are essentially the same as those in Test Methods E 8, and are compatible in technical content except that gage lengths are required to be 5D for most round specimens rather than 4D as specified in Test Methods E 8. Test specimens made from powder metallurgy (P/M) materials are exempt from this requirement by industrywide agreement to keep the pressing of the material to a specific projected area and density.
NOTE 3-Exceptions to the provisions of these test methods may need to be made in individual specifications or test methods for a particular material. For examples, see Test Methods and Definitions A 370 and Test Methods B 557M.
NOTE 4-Room temperature shall be considered to be 10 to 38°C unless otherwise specified.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
A 356/A356M Specification for Steel Castings, Carbon, Low Alloy, and Stainless Steel, Heavy-Walled for Steam Turbines A 370 Test Methods and Definitions for Mechanical Testing of Steel Products
B 557M Test Methods of Tension TestingWrought and Cast Aluminum- and Magnesium-Alloy Products [Metric]
E 4 Practices for Force Verification of Testing Machines
E 6 Terminology Relating to Methods of Mechanical Testing
E 8 Test Methods for Tension Testing of Metallic Materials
E 29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E 83 Practice for Verification and Classification of Extensometers
E 345 Test Methods of Tension Testing of Metallic Foil
E 691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
E 1012 Practice for Verification of Specimen Alignment Under Tensile Loading
Elongation
In reporting values of elongation, give both the original gage length and the percentage increase. If any device other than an extensometer is placed in contact with the specimen's reduced section during the test, this shall also be noted.
When the specified elongation is greater than 3 %, fit ends of the fractured specimen together carefully and measure the distance between the gage marks to the nearest 0.25 mm for gage lengths of 50 mm and under, and to at least the nearest 0.5 % of the gage length for gage lengths over 50 mm. A percentage scale reading to 0.5 % of the gage length may be used.
When the specified elongation is 3 % or less, determine the elongation of the specimen using the following procedure, except that the procedure given in 7.11.2 may be used instead when the measured elongation is greater than 3 %.
Prior to testing, measure the original gage length of the specimen to the nearest 0.05 mm.
Remove partly torn fragments that will interfere with fitting together the ends of the fractured specimen or with making the final measurement.
Fit the fractured ends together with matched surfaces and apply a force along the axis of the specimen sufficient to close the fractured ends together. If desired, this force may then be removed carefully, provided the specimen remains intact.
The use of a force of approximately 15 MPa has been found to give satisfactory results on test specimens of aluminum alloy.
Measure the final gage length to the nearest 0.05 mm and report the elongation to the nearest 0.2 %.
Elongation measured per paragraph may be affected by location of the fracture, relative to the marked gage length. If any part of the fracture occurs outside the gage marks or is located less than 25 % of the elongated gage length from either gage mark, the elongation value obtained using that pair of gage marks may be abnormally low and non-representative of the material. If such an elongation measure is obtained in acceptance testing involving only a minimum requirement and meets the requirement, no further testing need be done. Otherwise, discard the test and retest the material.
Elongation at fracture is defined as the elongation measured just prior to the sudden decrease in force associated with fracture. For many ductile materials not exhibiting a sudden decrease in force, the elongation at fracture can be taken as the strain measured just prior to when the force falls below 10 % of the maximum force encountered during the test.
Elongation at fracture shall include elastic and plastic elongation and may be determined with autographic or automated methods using extensometers verified over the strain range of interest (see 5.4). Use a class B2 or better extensometer for materials having less than 5 % elongation, a class C or better extensometer for materials having elongation greater than or equal to 5 % but less than 50 %, and a class D or better extensometer for materials having 50 % or greater elongation. In all cases, the extensometer gage length shall be the nominal gage length required for the specimen being tested.Due to the lack of precision in fitting fractured ends together,the elongation after fracture using the manual methods of the preceding paragraphs may differ from the elongation at fracture determined with extensometers
Doli Controller:
A/D-Conversion with high resolution (Standard: ±180.000 steps)Digital controlOwn power amplifieres for DC drivesAdditional parts like RMCs, aso.Complete delivery with a "Corporate Design"Simple communication between the producer software and the DOPE-InterfaceLarge Know-How in the range of testing techniquesOn-time deliveries
Main Configuration:
Load cell: Interface brand high accuracy load cell with max. deformation lower than 0.02mm. Tension and compression direction are available.
Reducer: Germany Nord reducer
Oil Station: Nachi Brand
Low noisy
Easy to installation and commissioning
Less thermal diffusivity, fast heat dissipation
Filtration accuracy: ≤5u
Over pressure protection
American Eton oil pipe and fitting
Specifications:
Model | HUT605A-TP |
Capacity | 600kN |
Accuracy class | 1 |
Column quantity | 6 |
Force range | 1%-100%FS |
Force accuracy | Better than ±1% of reading |
Force loading speed | 0.02%-2%FS/s |
Extension measurement range | 1%-100%FS |
Extension measurement accuracy | Better than ±1% of reading |
Extension resolution | 1/180000 of max. extension |
Displacement measurement accuracy | Better than ±1% of reading |
Distance between columns | 520mm |
Actuator (piston) speed | 0-140mm/min |
Diameter of round specimen | φ10-φ40mm |
Thickness of flat specimen | 2-30mm |
Max. tension space | 720mm |
Max. compression space | 630mm |
Actuator (piston) stroke | 250mm |
Diameter of compression platen | φ150mm |
Frame dimension (L×W×H) | 830×650×2500mm |
Oil station dimension (L×W×H) | 850×850×1900mm |
Net Weight | 3000kg |
Power supply | Three phase five lines, 380V±10%, 50Hz, confirm with final customer. |
Address:
Bldg. 3, Yinjin Technology Industrial Park, Shenzhen, Guangdong, China
Business Type:
Manufacturer/Factory
Business Range:
Instruments & Meters
Management System Certification:
ISO 9001, ISO 14001
Company Introduction:
Wance group, a company with all technical elites from testing machine industry, is determining to help customers build confidence and provide rapid and cost-saving design, development and production.
Wance group is founded by Shanghai wance testing machine Co., Ltd. And shenzhen wance testing machine Co., Ltd. Team members include both the industry′s top engineers and excellent management personnel from two big cities, with great geographical advantages. Within a decade, we strive to build wance into the top one in China and the top three in global testing machine industries.
Wance group is a high-tech enterprise integrating with R&D, manufacturing, sales, services, and professional mechanical testing solutions providing.
We have the best technology and products in China of electromechanical universal testing machine, servo-hydraulic universal testing machine, and automatic pendulum impact testing machine, fatigue testing machine and load calibration testing machine, also we have the top manufacturing technology of high performance and high precision pendulum impact and drop weight impact transducers.
Our products, services, and solutions are widely used in R&D, quality analysis and quality control field, covering testing equipment, testing technology and transfer system of a quantitative value. Customers cover aero-space, mechanical manufacture, vehicle, ship, construction, biological materials, college, universities, research institutes, national quality inspection institutes, export and import inspection institutes. We are keeping tight cooperation with all factories, research institutes, and quality inspection organizations, and providing high quality products and services along with customer uptime demands.
From small melt flow indexer to big 50000j drop weight impact testing machine, wance group relies on years of industrial expertise and creative technical team, delivering the greatest test support and confidence to customers across a wide range of fields. Wance group is committed to accelerate the innovation of test technology and test equipment, to support research projects, to motivate enterprises in brand development and improvement, and products selling in global market.
We are committed to provide complete products and solutions deeply and widely. Wance will be your primary and reliable partner!